Welcome to Würth Taiwan For trade customers only

Furnace putty 1000

Sealing compound, Fire cement 1000
PUTY-HTEMP-OVENCEMENT1000-310ML

Art.-no. 08932900
EAN 4045989813865
Prices for customers after login
Furnace putty 1000

Art.-no. 08932900

Prices for customers after login
Quantity
PU

Exclusively for trade customers

Register now and access more than 125,000 products

Solvent-free 1-component sealing compound with optimum heat resistance, high degree of strength and excellent adhesion to metal surfaces

No formation of sediment


The individual constituents do NOT separate during storage



Ready for use


No prior stirring is necessary as with products in tubs, for example


Easy to apply with a cartridge gun



Frost-resistant


Storage temperatures below 0 °C (approx. -5 °C) possible



Silicone-free

Notice

When dry after curing, the putty is not elastic.

The usage instructions are recommendations based on the tests we have conducted and our experience; carry out your own tests before each application. Due to the large number of applications and storage and processing conditions, we do not assume any liability for a specific application result. Insofar as our free customer service provides technical information or acts as an advisory service, no responsibility is assumed by this service except where the advice or information given falls within the scope of our specified, contractually agreed service or the advisor was acting deliberately. We guarantee consistent quality of our products. We reserve the right to make technical changes and further develop products.

Product information

Datasheets(X)

Safety data sheet

Certificates/ Documents

 | 

 | 

Application area

For sealing in the heating equipment sector, such as sealing boilers, ovens, cookers, chimneys, burner chamber fittings, smoke gas pipes and a wide range of equipment and apparatus in the high-temperature sector up to 1,000 °C. It can also be used in place of sealing cords in boiler system doors following an annual inspection or after cleaning.

Instructions
  • The surfaces must be clean, dry, free from grease and unpolished

  • Further information in the technical data sheet

Chemical basis

Water glass luting with mineral fillers

Contents

310 ml

Container

Cartridge

Max. temperature resistance

1000 °C

Density

2.21 g/cm³

Colour

Cast grey

Recoatable/Can be painted over

Yes

Smell/fragrance

Neutral

Viscosity/consistency

Pasty

Long-term elasticity

Virtually no elasticity

Shrinkage

Minimal

Curing time

2 d

Full curing speed

1 mm/d

Water-soluble

Not readily soluble in water

Min./max. temperature resistance

-5 to 1000 °C

Min./max. processing temperature

5 to 30 °C

Resistance against

Fats
Household cleaning products
Oil
Flue gases and their condensates

Shelf life from production/conditions

12 Month / in sealed cartridge, max. 30°C

Suitable glove:
 
Product
Description
Nitrile chemical protective glove With cotton velour finish inside
Nitrile chemical protective glove With cotton velour finish inside
Description:
Permeation level: 6
Permeation is the process by which a chemical moves through the material of a protective glove on a molecular level. The time from the initial contact between the chemical and the glove to the permeation of the material is the breakthrough time.
Measured breakthrough time
Permeation level
< 10 min
0
≥ 10 min
1
≥ 30 min
2
≥ 60 min
3
≥ 120 min
4
≥ 240 min
5
≥ 480 min
6

Important information:

The information given is based on experience and laboratory conditions and is designed as a guide. However, the actual suitability of a glove depends on the individual conditions of its use and must be confirmed by an appropriate test under operational conditions. Given the variety of materials and chemicals used, the possibility of incompatibility or usage problems for the wearer cannot be excluded in individual cases. We would be happy to advise you about optimum solutions.

Art.-no.
Cust. Mat. No.

Hazardous Material

Product information

Datasheets()

Datasheets ()

CAD data  | 

Certificates/ Documents

 | 

 | 

Technical information